Skip to content
Illustration: a mobile crane with its boom raised against a dusk sky, outriggers set on wet ground.

Before the lift, the inspection.

Third-party equipment inspection and HSE training for sites across the UAE.

  • ENAS accredited inspection body
  • EIAC accredited inspection body
  • ADNOC pre-qualified supplier
  • ACTVET licensed training provider
  • Highfield Qualifications approved centre
The same crane drawn as a technical line plate.
  • Wire rope
  • Telescopic boom
  • Hook block
  • Luffing cylinder
  • Counterweight
  • Carrier
  • Outriggers

Then we look closer.

Every examination is matched to the equipment and the applicable standards.

  • Visual inspection
  • Functional testing
  • Dimensional checks
  • Load testing (where applicable)
  • NDT coordination (where applicable)
  • Documentation review

Equipment we cover

Clear reports for your HSE team and site management, and certification where the requirements are met.

Not sure where your requirement fits? Tell us what you have and where it is, and our team will take it from there.

Discuss your requirements

Independent, with the paperwork to show it.

MSC is accredited by ENAS and EIAC to ISO/IEC 17020:2012 as a Type A inspection body. Each credential below is labelled with what it is.

Inspection accreditation

  • Inspection accreditation

    ENAS

    accredited inspection body

    ENAS accredited inspection body (ISO/IEC 17020:2012, Type A)

    Reference
    NAI 091
    Valid to
    22/08/2028
    Enquire about our accreditation
  • Inspection accreditation

    EIAC

    accredited inspection body

    EIAC accredited inspection body (ISO/IEC 17020:2012, Type A)

    Reference
    IB-113
    Valid to
    03/06/2029
    Enquire about our accreditation

Supplier pre-qualification

Training credentials

  • Training licence

    ACTVET

    licensed training provider

    Licence
    1374/2026
    Valid to
    11/03/2027
    Request credential details
  • Centre approval

    Highfield

    Qualifications approved centre

    Highfield Qualifications International Approved Centre

    Centre number
    46736
    Valid to
    21/08/2027
    Request credential details

Established in Abu Dhabi in 2010. All credentials and validity dates

Need these for a project or vendor registration?Request accreditation and approval details

From request to report

Start with a request
  1. 1

    Request & scope

    Tell us the equipment, quantity and location. We confirm the scope and site access.

  2. 2

    Site attendance

    The inspector attends on the agreed date and time.

  3. 3

    Examination & testing

    Visual, functional and applicable testing, selected for the equipment type and applicable standards.

  4. 4

    Findings & actions

    Defects and observations are documented.

  5. 5

    Report / certificate

    Report issued, with a certificate where requirements are met.

What you receive

Documentation review
Review of the equipment documentation you have available.
Findings and report
Inspection findings documented in a clear inspection report.
Certificate where requirements are met
A certificate is issued where applicable and the compliance requirements are met.
Reinspection guidance
Clear guidance on defects and reinspection where deficiencies are identified.

HSE and operator training for your site teams

Practical, instructor-led courses built around real site hazards and safe procedures.

An MSC engineer in a white hard hat and high-visibility vest checks a document with site workers beside a wheel loader
MSC engineer with a site team beside a wheel loader.
An MSC trainer pointing to a slide during a classroom safety session
Classroom session.
An MSC engineer explaining a point to a site team beside a wheel loader
On-site briefing.
  • ACTVET licensed training provider, licence 1374/2026 (disciplines: First Aid, Safety and Security).
  • Highfield Qualifications International Approved Centre, centre no. 46736.
All training courses

Tell us what needs inspecting.

Tell us your equipment, location and requirements. Our team will confirm the scope, delivery arrangements and quotation.

Office+971 2 553 5560

WhatsApp+971 52 766 7556

Emailinfo@mastersafety.ae

Background: rendered illustration.

Request a quotation

Five required fields. Our team will contact you to confirm the scope and quote.

Add equipment details (optional)

Or call +971 2 553 5560

Your details are used only to respond to this request. See the privacy notice.